← Guides

What should line clearance records show, and how are they reviewed?

By Savi C., Co-Founder · Published Nov 16, 2026

What the regulations require

Line clearance exists to prevent mix-ups: the wrong tablets, leaflets or labels from the previous run ending up in the next one. In the US, 21 CFR 211.130 requires written procedures for packaging and labeling operations, and paragraph (e) requires inspection of the packaging and labeling facilities immediately before use. The inspection confirms that all drug products from previous operations have been removed, and that packaging and labeling materials not suitable for the next operation have been removed too. The results go into the batch production record. Section 211.188(b)(6) adds that the batch record documents inspection of the packaging and labeling area before and after use.

In the EU, Chapter 5 paragraph 5.50 requires steps before packaging begins to ensure the work area, packaging lines, printing machines and other equipment are clean and free from any products, materials or documents previously used, if they are not required for the current operation, and says line clearance should follow an appropriate checklist. Paragraph 5.40 applies the same idea before processing operations, and Chapter 4 paragraphs 4.18(c) and 4.19(f) and (g) build the checks into the processing and packaging instructions. ICH Q7 paragraph 9.44 sets a similar expectation for active substance packaging, allowing the result to be recorded in the batch record, the facility log or another documentation system.

What a line clearance record should show

Element

Line or room identity, and the product and batch being cleared out

Why it matters

Proves which changeover the check covers

Element

The product and batch about to start

Why it matters

Shows the check was made against the right next operation

Element

Each checklist item marked individually: product, components, printed materials, documents, reject bins, machine pockets and printers

Why it matters

A single tick for the whole list cannot show what was checked

Element

Date and time of the check

Why it matters

Lets review confirm it happened immediately before use and before the first packaging entry

Element

Who performed the check, and who verified it where your procedure requires

Why it matters

Makes the check attributable and the verification real

Element

Removal and destruction of leftover batch-coded materials

Why it matters

EU GMP 5.62 requires unused batch-coded packaging materials to be destroyed and the destruction recorded

Element

Any finding during the check and what was done about it

Why it matters

An item found is an event to record, not something to quietly remove

Reviewing line clearance in the packaging record

Timing and sequence

  • The clearance for this batch is dated and timed before the first packaging or labeling entry
  • The previous batch named on the clearance matches the previous batch in the line logbook
  • The after-use inspection for the previous batch is recorded, as 211.188(b)(6) requires

Content

  • The checklist used is the current approved version for that line
  • Every item is completed individually, with no blanks and no item marked not applicable without a reason
  • Signatures belong to people trained on the procedure, and performer and verifier are different people where two are required

Findings and follow-up

  • Any material found during clearance is recorded, with a deviation where your procedure requires one
  • Interruptions in the run, such as a line stop or a change of printed materials, have a further clearance where the procedure requires it
  • Label and printed material reconciliation for the batch is consistent with the clearance, with no unexplained surplus or shortfall

Where review usually catches problems

Most line clearance problems in review are sequence problems. A clearance timed after the first packaging entry, or naming a different previous batch from the one in the line logbook, suggests the check was completed from memory or after the fact. The other common problem is a checklist completed with a single signature across every line item, which does not show that each location was checked. Reconciliation is a useful backstop: a label count that does not reconcile, read alongside the clearance record, can point at a clearance that missed something. The guide How do you check yield and reconciliation in batch records? covers that side.

How Litewave fits

Litewave reads paper or electronic records, checks every entry against your master record and specifications, and shows QA only the exceptions, each linked to the page it came from. For line clearance that includes timing against the first packaging entry, blank or unsigned items, and a previous batch that disagrees with the line log. Litewave proposes, qualified people approve.

Questions we get asked

Does the regulation require a second person to verify line clearance?

21 CFR 211.130(e) requires the inspection and its documentation in the batch record but does not itself specify a second person. Many sites require an independent verification by procedure, and once it is in your procedure, the record must show it.

Is line clearance only for packaging?

No. EU GMP Chapter 5 paragraph 5.40 applies the same principle before processing operations, and 21 CFR 211.67(b)(6) requires equipment to be inspected for cleanliness immediately before use. Packaging gets most attention because printed materials create the highest mix-up risk.

Who reviews the line clearance record?

It is part of the packaging and labeling records, which 21 CFR 211.192 requires the quality control unit to review and approve before a batch is released. Production usually reviews it first, and QA reviews it as part of batch review.

Sources

  1. 21 CFR 211.67, Equipment cleaning and maintenance (eCFR)
  2. 21 CFR 211.130, Packaging and labeling operations (eCFR)
  3. 21 CFR 211.188, Batch production and control records (eCFR)
  4. 21 CFR 211.192, Production record review (eCFR)
  5. EudraLex Volume 4, Part I, Chapter 5, Production
  6. EudraLex Volume 4, Part I, Chapter 4, Documentation
  7. ICH Q7, Good Manufacturing Practice Guide for Active Pharmaceutical Ingredients