How do you review cleaning records and keep them consistent with cleaning validation?
By Savi C., Co-Founder · Published Nov 16, 2026
What the regulations require
21 CFR 211.67(a) requires equipment and utensils to be cleaned, maintained and, as appropriate, sanitized or sterilized at appropriate intervals to prevent contamination that would alter the drug product. Paragraph (b) requires written procedures that include assignment of responsibility, cleaning schedules, a description of methods, equipment and materials in enough detail, removal or obliteration of previous batch identification, protection of clean equipment before use, and inspection for cleanliness immediately before use. Paragraph (c) requires records as specified in 211.180 and 211.182. FDA’s 1993 Guide to Inspections, Validation of Cleaning Processes, sets out what investigators look for in cleaning procedures and validation.
In the EU, Annex 15 section 10 covers cleaning validation. Several of its paragraphs set conditions that routine records then have to stay within. Paragraph 10.2 says a visual check alone is not generally acceptable as the acceptance criterion, and that repeated cleaning and retesting until acceptable residue results are obtained is not an acceptable approach. Paragraph 10.8 asks for dirty and clean hold times to be defined. Paragraph 10.9 says the maximum campaign length, in time or number of batches, should be the basis for validation where campaigns are run. Paragraph 10.15 says that where cleaning is manual, its effectiveness should be confirmed at a justified frequency. For active substances, ICH Q7 paragraph 12.76 asks for cleaning procedures to be monitored at appropriate intervals after validation.
Why consistency with validation is the real question
A cleaning record can be complete, signed and on time, and still describe a clean the validation never covered. The validation proved a specific procedure works under specific conditions. If the equipment sat dirty longer than the validated hold time, the campaign ran one batch past its validated length, or a different detergent concentration was used, the routine record no longer has the validation behind it. Review has to compare the record with the validated conditions, not only with the SOP.
The same logic applies to repeat cleaning. If a clean fails its visual inspection or a residue test and is simply repeated until it passes, Annex 15 paragraph 10.2 treats that as unacceptable as a validation approach, and in routine operation it is a signal that the procedure may not be working as validated. It should be recorded and assessed, not absorbed into a second signature.
Validated condition and what the routine record must show
Validated condition
Cleaning procedure and version
What the routine cleaning record must show
The procedure and revision used, matching the one validated or a version assessed under change control
Validated condition
Detergents and concentrations
What the routine cleaning record must show
Detergent or cleaning solution, lot and concentration within the validated range
Validated condition
Dirty hold time
What the routine cleaning record must show
End of processing and start of cleaning times, with the interval inside the limit
Validated condition
Clean hold time
What the routine cleaning record must show
End of cleaning and next use times, with the interval inside the limit
Validated condition
Campaign length
What the routine cleaning record must show
Number of batches or elapsed time since the last full clean, inside the validated maximum
Validated condition
Equipment and products covered
What the routine cleaning record must show
The equipment ID and previous product are within the validated scope or the worst case it represents
Validated condition
Acceptance criteria
What the routine cleaning record must show
Visual inspection result and, where required for routine verification, residue or swab results against the limit
Cleaning record review checklist
The record itself
- Equipment ID, previous product and batch, and cleaning type (full or minor) recorded
- Performed by and checked by signatures and dates present, as 211.182 requires
- Previous batch identification removed or obliterated, as 211.67(b)(4) requires
- Inspection for cleanliness recorded immediately before the next use
Against the validation
- Dirty and clean hold times calculated from recorded times and within limits
- Campaign count or duration since the last full clean within the validated maximum
- Previous product covered by the validation or its worst case product
- Any routine residue or swab result within its limit, with no unexplained retest
Across records
- The cleaning entry in the equipment log agrees with the cleaning record and the batch record
- No repeated cleaning on the same changeover without a recorded reason and assessment
- Changes to procedure, detergent or equipment since validation were assessed under change control
How Litewave fits
Hold times and campaign counts are arithmetic across several documents, which is where manual review slips. Litewave reads paper or electronic records, checks every entry against your master record and specifications, and shows QA only the exceptions, each linked to the page it came from. Your validated limits become checks it applies to every cleaning record, and Litewave proposes, qualified people approve. The related guide How should equipment use and cleaning logbooks be reviewed? covers the logbook side.
Questions we get asked
Is a visual inspection enough to release equipment after cleaning?
For routine release, your validated procedure decides. For cleaning validation, EU GMP Annex 15 paragraph 10.2 says a visual check is an important part of the acceptance criteria but is not generally acceptable on its own.
What happens if a hold time is exceeded?
The cleaning falls outside its validated conditions. Treat it as a deviation under your procedures: assess the impact, decide whether extra cleaning or verification is needed, and record the decision before the equipment is used.
Do cleaning records need to be reviewed at batch release?
Yes, as far as they bear on the batch. 21 CFR 211.192 requires review of all production and control records before release, and the cleaning that preceded the batch is part of the evidence that the equipment was fit for use.
Sources
- 21 CFR 211.67, Equipment cleaning and maintenance (eCFR)
- 21 CFR 211.182, Equipment cleaning and use log (eCFR)
- 21 CFR 211.192, Production record review (eCFR)
- FDA, Guide to Inspections, Validation of Cleaning Processes (July 1993)
- EudraLex Volume 4, Annex 15, Qualification and Validation
- ICH Q7, Good Manufacturing Practice Guide for Active Pharmaceutical Ingredients
